The Little Sink That Could

One of the latest trends in bathroom design is the bath micro sink. Though it seems a bit odd, this new fixture can be very useful in smaller Seattle bathrooms or in bathrooms where several people need to share the facilities. These sinks are used in kitchens, laundry rooms, and other areas of the home as well.

Space Considerations

A micro sink is about the size of a three-ring binder lying flat.  These sinks require very little in the way of plumbing. You should be able to run one small pipe to the sink and allow it to connect to any other water supply in the room. If you have any difficulty, just call your Seattle plumber, who can install your sink for you in no time.   The micro sink is especially attractive if you do not have the space available to put in new cabinets. You can sit the micro sink on any surface, including crates or other removable storage.

Built-in Accessories

Because the sinks are designed for people to use without the convenience of other bathroom supplies, they often come with soap holders or dispensers on them. You may even find a micro sink with a rack on the side. These features allow you to put extra toiletry items there for easy use. The micro sink in the Seattle bathroom can be placed next to a mirror for ease of use.

Benefits of a Bath Micro Sink

The primary purpose of a micro sink is to allow for an extra person to get ready with very little space. While two-sink bathrooms are very popular, particularly in master bathroom suites, already-built homes may not have the space needed to make adding another entire sink unit, even with a pedestal, a possibility. Instead the micro sink permits you to make space for a second adult – or teen! – to get ready in a bathroom without making any major changes.

A micro sink also allows you to add a great feature without a lot of work in terms of re-running plumbing lines. Often adding a second sink means tearing out the backsplash or drywall, which can become a monstrous chore, but the micro sink can connect easily to existing plumbing lines.

Half-Bath Ideas

You also can have a micro sink in a half-bath where you have little room. In a half-bath, you will not need to store anything except an extra hand towel and toilet paper. You can use a small decorative basket for these storage needs and then put a micro sink in the room. You can add this bathroom for very little square footage, and it will increase the value of your Seattle home. This type of sink also works with a half-wall bathroom set-up because you can put the sink along the wall or beside it.

Handicapped Ease

Micro sinks also work well for handicapped people who need to use a restroom. People in wheelchairs often need to be able to access the sink without the bulk of the cabinets underneath, and a micro sink provides the perfect opportunity for this set up.

What to Look for in a Micro Sink

Price

The key will be finding a good price for a micro sink above all else. Work to find the lowest prices you can by scouring the Internet, wholesalers, and Seattle home improvement stores. Since these sinks are new and trendy, though, they tend to be on the more expensive side.

Shape

Also check for a shape that will work in the space you have. Measure your space now so that you can compare it to the options available. As the micro sinks are so small and are intended for tight spaces, you will find that they come in unique sizes. While a triangular sink will work for some people, it may not for you. Check out these issues before you buy and install.

Design

Overall, though, you will be looking for a design that matches the décor that you have going in your Seattle bathroom. A micro sink is meant to be an add-on, not the main focus, so the sink you will be most happy with is the one that blends.

Article Source: http://homeimprovement.lovetoknow.com/Bath_Micro_Sink

Click here or call 877-694-5176 to schedule an appointment.

Stop. Gate. Ball. May the Best Valve Win

There are three basic valve styles, making this a classic case of good, better and best (described in order as follows). All three can be used for water, oil or airflow control if the casting has “WOG” stamped on it. Your Tacoma plumber is well versed in all three of these types of valves and can steer you in the right direction when it comes to which will best suit your needs. Read up on the three basic types before you attempt any plumbing repairs on your own.

Stop valves are closed by screwing a rubber gasket down onto a seat in the middle of the valve. Tacoma pros only use small versions that act as shutoff valves for fixtures such as sinks and toilets and outdoor sillcocks. Flow is inefficient because of the circuitous route the fluid (water, in most cases) has to follow. It’s important to orient the valve in the right direction with the arrow (cast into the side of the valve) aligned with flow direction. That way, water flows against the bottom of the rubber gasket. If the valve is put in backward, the flow will force the gasket away from the top of the valve.

Gate valves are called “full-flow” valves; there’s a direct unobstructed path for flow right through the middle of the valve. A wedge-shaped brass gate is lowered into a machined slot to close the valve. They should either be completely open or completely closed. Water flowing through a partially open gate valve wears away the metal and causes the valve to fail over time.

Ball valves contain a finely machined stainless steel ball with a hole drilled through the center that pivots in plastic bushings. Like the gate valve, it’s a full-flow valve. The hard steel allows this valve to be partially open without wearing out. In the closed position, the lever is perpendicular to the pipes; in the open position it’s parallel, so a glance will tell you if it’s open or not. The downside? If the pipes are tight against your Tacoma wall, you may not be able to operate the lever.

Article Source: http://www.familyhandyman.com/DIY-Projects/Saving-Money/Buying-DIY-Supplies/plumbing-valve-basics

Click here or call 877-694-5176 to schedule an appointment.

Nothing Silly About Plumber’s Putty

Plumber’s putty is a substance used to make watertight seals between pipes and countertops. It will remain soft for a long while after it is used. This characteristic makes plumber’s putty ideal for seals you will need to reverse. Because it does stay soft for such an extended amount of time, you shouldn’t use plumber’s putty on pipes that will experience any amount of water pressure; the seals will not hold up to such pressure. The putty is fairly easy to use and can be wiped away if you make a mess. Read below to discover common uses for plumber’s putty.

 

Sinks

You can use plumber’s putty around the rim of the sink to create a watertight barrier, but you should not use it if your  Seattle countertop is granite or another kind of stone. It is compatible with Formica countertops.

If you form the seal correctly, no water will be able to seep into the area under the sink and create mold or water damage. In order to install the sink correctly, apply the soft plumber’s putty to the bottom of the sink and place, with pressure to the countertop. Some sinks come with clips meant for the bottom of the sink (under the countertop). The clips ensure that the proper amount of pressure is placed on the plumber’s putty for it to be effective.

Drains

You may use plumber’s putty to seal drains in the sink or the bathtub. Like with the installation of a sink, you should place the putty underneath the drain before you place the drain. Then you should apply pressure in order to create a watertight bond.

 

Toilets

To seal a toilet to the floor, you may use plumber’s putty. However, you should exercise caution. If you seal the toilet all the way around and it develops a leak somewhere, the water will be trapped in. The water will then rot the floor without any signs. In order to avoid this scenario, don’t seal the toilet all the way around. Then any seeping water will alert you of a leak.

 

Pipes and Plumbing

Plumber’s putty in pipes and plumbing does not hold up to water pressure. Use plumber’s putty only on pipes that will not experience a great deal of pressure. To seal pipes together, place the putty on the inside of the pipe, where the threads will twist together. Twist the other end of the pipe into the threads and the putty. Wipe away excess putty and allow time for it to set.

Exercise caution whenever you use plumber’s putty, as it contains oils that can discolor some surfaces. You generally should not use it on granite, plastics, marble or any other porous surfaces. (You can find certain brands, though, manufactured for use on surfaces such as these.) Be sure to read the warnings on your plumber’s putty in order to avoid these problems.

 

Plumber’s putty is an extremely useful substance – but not appropriate for all plumbing repairs.  Contact your Seattle plumber should the job prove too much to handle by yourself.
Read more: http://www.doityourself.com/stry/4-different-uses-for-plumbers-putty#ixzz1p6SuqYBe

Click here or call 877-694-5176 to schedule an appointment.

Too High? Too Low? Just Right!

If you are experiencing low or high water pressure, there are a few things that you can
check to see if the pressure problem is in your household pipelines.

First, check the pressure/flow at your outside hose bib, usually located in the front of
your home. If you are getting good flow at the hose bib, the problem may be isolated
inside your Tacoma home. If the problem appears only on kitchen and bathroom sink taps, make
sure the faucet screens are free of accumulated hard water deposits or sediment. If all taps
are affected, make sure your main shut-off valve is fully opened and your pressure
regulating valve, if you have one, is operating properly. If you have a water conditioning
system (softener, etc.) verify that it is operating properly.

If there is very little pressure and flow from the hose bib, check your gate valve that is
located on the standpipe to make sure it is turned on all the way. If your gate valve is on
all the way, your pressure regulator may need to be adjusted or replaced. This pressure
regulator is the Tacoma homeowner’s responsibility to maintain.

Water Pressure Regulators for Residential Use

New residential plumbing codes usually require a pressure regulator be installed.
Although most pressure regulators are adjustable, they are normally set at a pressure
between 50 and 70 psi which is considered normal pressures for residential uses.
Regulators are typically installed with the initial construction of the home and maintained
by the property owner. Regulators are always located above
ground, usually near where the plumbing enters the house.
The pressure regulator is a bell-shaped device and is typically
installed on the inlet pipe, next to the hose bib and house valve.
The regulators are preset by the manufacturer at about 45 – 55
psi., and areas with low pressures may be negatively impacted
with this setting. Although in most cases, they do not need to
be adjusted. Please note that incorrectly adjusting the regulator
could cause water pressure that is too low or too high inside the
home. We recommend you have a qualified Tacoma plumber make adjustments to the pressure
regulator.
In an effort to aid you in your water pressure problems this information is being provided
to help you make adjustments to the water pressure regulator in your Tacoma home (if equipped).
This device will not increase water pressure above the operating pressure of the city
maintained water main.

These are generalized instructions actual adjustment procedures may vary depending on
the type and model of the pressure regulator in you home. To assure accurate
adjustments are made please refer to the literature that is provided by the manufacturer of
the regulator.

To increase the pressure down stream of the pressure
regulator loosen the Retainer/Lock Nut on the stem, them
rotate the Pressure Adjustment Stem clockwise to increase
the pressure and counter clockwise to reduce the pressure.
A pressure gauge connected down stream of the regulator
can be used to verify an increase or decrease in pressure.
Another method to verify the change in pressure is to set a
lawn sprinkler in the yard and view the effect of adjusting
the pressure regulator.

In some cases the internal components of the pressure regulator may need to be cleaned,
to perform this procedure please refer to the manufactures recommended maintenance
instructions or contact a licensed Tacoma plumber. If you chose to perform maintenance on the
pressure regulator such as cleaning of the internal seats and screens be sure to shut the
water off before the regulator before you proceed.

The adjustment and or cleaning of the screen of the pressure regulator may or may not
increase the pressure within your Tacoma home. Should you continue to experience water pressure problems having completed all these steps, you need to contact your Tacoma plumber.

Article Source: http://www.ofallon.mo.us/pubs/Water_tips.pdf

Click here or call 877-694-5176 to schedule an appointment.

Plumbing Pratfalls

No one wants to face expensive but avoidable plumbing repairs.  There are going to be times when calling your Seattle plumber is inevitable – but to lengthen the time between housecalls, avoid these plumbing errors.

Putting grease down the sink -Please don’t put grease down the drain.  Even with hot water and soap, grease can build up over time causing problems with your pipes.

Using your sink as a trash can – Even if you have a garbage disposal, that does not give you a free pass to dump everything and anything down the drain.  Food chunks in the kitchen or hair and fingernails in the bathroom serve as the start of a terrible clog.

Using the toilet as a trash can – The toilet has its given role, the trash can has another.  Do not confuse the two.

Using too much Drain-O – Using drain cleaner too often or on the wrong type of clog could lead to erosion of your pipes or just a really nasty clog for your Seattle plumber to clean out.

Mixing metals – If you decide to replace the pipes yourself for a portion of your Seattle home’s plumbing system, please do not mix piping metals.  This can lead to corrosion, leaks, and a number of other headaches.

Lack of insulation – If you live in a cold climate, your pipes can freeze in the winter unless they are properly insulated.

Leaving hoses attached – Leaving the hose attached to your outdoor faucet through the winter can lead to frozen pipes or a damaged faucet.

Pouring chemicals in a septic system – If you have a septic system, please research what is safe and what is not for septic systems.  Certain chemicals can kill the good bacteria there leading to a smelly, expensive mess.

Messing with plumbing vents – Your Seattle home’s plumbing vents are there for the plumbing, not for a quick and easy way to rewire anything in your house.  Don’t mess with the vents.

Accidentally cutting hidden plumbing - Use caution as you remodel or cut into the walls in your Seattle home.  Cutting into a hidden pipe can cause extensive leaking and time consuming damage.

Article Source: http://plumbinghelptoday.com/denver-plumbing-repair-blog/2012/01/10-things-that-will-ruin-your-plumbing/

Click here or call 877-694-5176 to schedule an appointment.

Hammer Time! (Sorry MC – WATER Hammer)

Water hammer is a specific plumbing noise, not a generic name for pipe clatter. It occurs when you shut off the water suddenly and the fast-moving water rushing through the pipe is brought to a quick halt, creating a sort of shock wave and a hammering noise. Plumbing that’s properly installed has air chambers, or cushions, that compress when the shock wave hits, softening the blow and preventing this hammering. The chambers can fail, though, because water under pressure gradually absorbs the air.

If you never had hammering and then it suddenly starts, most likely your Seattle plumbing system’s air chambers have become waterlogged. You can cure water hammer by turning off the water behind the waterlogged chamber, opening the offending faucet and permitting the faucet to drain thoroughly. Once all the water drains from the chamber, air will fill it again and restore the cushion. If the air chamber is located below the outlet, you may have to drain the main supply lines to allow the chamber to fill with air again.

The air chamber will not drain properly if it’s clogged with scale or residue from chemicals or minerals in the water. The chamber always should be larger than the supply pipe to preclude such clogging. Since the chamber is simply a capped length of pipe, however, all you have to do to clear it is remove the cap and clean out the residue.

What do you do if there are no air chambers built into your plumbing system? You must do something, because water hammer pressures may eventually cause damage: failure of fittings or burst pipes, for example. Because water hammer is most often caused by water pressure that’s too high, the first step is to reduce the water pressure if possible. Sometimes this isn’t feasible because a reduction in pressure may result in only a dribble of water at an upper-floor faucet if one on the first floor is turned on.

Where the idea is a workable one, you can reduce pressure by having your Seattle plumber install a pressure-reducing valve in the supply line that comes into your Seattle home. The same purpose is served by installing a globe valve at the head of the affected pipeline. But this too may result in pressure too low for proper operation when other faucets are open.

If pressure reduction is not feasible or is ineffective, install the necessary air chambers to prevent water hammer. If you have no room to make the installation without tearing into a wall, go to a Seattle plumbing supply dealer and find out about the substitute devices designed for such problem areas. Many of these devices have a valve that makes it easy for air to re-enter the system.

The next time you hear noises or clatter coming from your Seattle home’s plumbing system, try the solutions mentioned in this article. The same goes for leaking, sweating, or frozen pipes. If you can solve the problem right away, you can prevent it from becoming more serious.

Article Source:  http://home.howstuffworks.com/home-improvement/plumbing/how-to-fix-pipes5.htm

Click here or call 877-694-5176 to schedule an appointment.

Pipes That Go Bump in the Night

Water flowing in pipes can cause all kinds of weird noises. We all know what water running through a pipe sounds like, but what about some of those other plumbing sounds – like creaks or cracking sounds, rattling, whistling and the most annoying or scary of them all, that loud banging noise? Let’s look at what causes those sounds and how you can fix them.  You should be able to manage most of these, but if the problem persists you should seek the service of your Tacoma plumber. He can easily handle any pipe repair or installation that may be necessary.

Creaks or a cracking sound
These are usually caused by the expansion and contraction of the water pipes themselves. As hot water runs through a pipe, it naturally heats the pipe, causing it to expand slightly. Once the water stops flowing, the pipe cools and the metal contracts, resulting in the creaking or cracking sound. The easiest way to fix this is to put some insulation around the pipe, or if the pipe is running through a tight fitting hole in the wood framing, cut a notch in the framing so the pipe can expand and then contract without that creaking sound.

Rattling
The cause and remedy are similar to the cracking sound. The rattling sound comes from the pressure of water running through a loosely attached pipe, causing it to vibrate slightly. When a loose pipe vibrates against something solid, like framing or the strapping designed to hold it tightly, you hear the rattling sound. Stopping the pipe from vibrating will fix the rattle. Put some cushioning around the pipe or fasten the strapping more securely so the pipe won’t vibrate.

Whistling
This is usually caused by water flowing through a restricted section of the plumbing. The restriction can be sediment in the pipe or a defective washer or valve. If the whistling only occurs when a particular faucet is turned on, that’s likely where the problem is, and replacing the washer or repairing the valve seat should fix it. However, if the whistling sound occurs when any faucet is turned on, the problem is more likely in the main water supply valve itself. Adjusting the water pressure at the main water valve may dislodge the impediment, or the change in water pressure itself could get rid of the whistling sound. If that doesn’t eliminate the problem, you may have to get the water valve replaced.  This is most likely a task for your Tacoma plumber.

Banging
The loud banging sound when you shut off the water flow is actually called “water hammer,” and is a fairly common complaint in older Tacoma homes. The flow of water through the pipes contains energy, and when the flow is abruptly stopped, this energy causes the loud banging sound. Initially a home’s plumbing system was built with short pieces of pipe that filled with air and acted as air cushions to absorb the water’s energy when the flow was stopped abruptly. However, over time the air has leaked out, meaning there is no air cushion left to absorb the water energy.

You can put that air cushion back into your plumbing system by turning off the main water supply and opening all the faucets in your Tacoma home to drain the system. Next, turn the water supply back on and work your way up through the house, turning off the faucets as water flows through them. This should trap some air in the air chamber so it will once again provide the cushioning effect. If this doesn’t work, you can buy a “water hammer arrester” that attaches directly to the water supply pipe where the water hammer originates.

If your Tacoma plumbing is making any of these sounds, you should be listening because it’s telling you it needs some plumbing maintenance. The sound is caused by something not working properly in your system and if you ignore it, over time, that small sound could lead to larger problems.

Read more: http://www.doityourself.com/stry/waterhammer#ixzz1mHkQ1peF

Click here or call 877-694-5176 to schedule an appointment.

Take the Plunge

There are several different types of plungers available to clear partially or completely clogged drains, but all use basically the same principal. A plunger is used to create a positive or negative pressure inside the pipe to loosen the blockage and allow it to flow down the drain. As a first line of defense against any clog, a plunger is a safe bet.  However, if you’re clog proves to be too much for this simple tool, your Seattle plumber can handle any clog you’ve got.

Sink Plunger

This is the standard plunger that we all recognize and has probably been around as long as indoor plumbing. Consisting of a pliable rubber cup and handle, this plunger is capable of creating both a positive pressure (by forcing the cup down) and a negative pressure (vacuum) when pulled away from the fixture. Variations on the design are typically limited to the size of the cup and length of the handle.

The sink plunger; as it name suggests, is best used on sinks or relatively flat fixtures to which it can create a suction seal. When using the sink plunger:

• Cover the overflow hole of the sink or tub;
• Keep the fixture partially full of water, because water is not easily compressed it will place a stronger force on the blockage;
• Plunge forcefully in both directions for several minutes until the drain clears.

Toilet Plunger

The toilet plunger is very similar to the sink plunger but has a larger cup and a fold out flap that will fit into the trap of the toilet. The flap can also be left folded in for use on sinks, floor drains and other fixtures. If used correctly, this plunger will clear nearly all toilet clogs and should be your first line of defense before calling your Seattle plumber. To use a toilet plunger follow these steps:

• Fold out the flap on the plunger;
• Keep the toilet about half full of water;
• Insert the plunger so that the folded out cup goes into the drain opening and try to form a suction seal with the toilet bowl;
• Being careful not to splash yourself, forcefully plunge up and down several times and remove the plunger. Repeat adding more water if necessary.

You want to test and see if the toilet will drain once you think you’ve cleared the clog, but don’t do this by flushing the toilet again until you’re sure the clog is removed. To test for drainage you have to add water. This can be done one of two ways.

The first way is to slowly pour water into the toilet as from a bucket.

The second way is to open the toilet tank lid and SLOWLY lift the flapper seal at the bottom of the tank until water begins to enter the bowl. Do not lift the flapper all the way up or else the toilet will flush.

If water goes down the toilet easily, the clog is cleared. If not, then try again by repeating the previous step and this step a time or two more.

Article Source:  http://www.plumbinghelp.ca/articles_types_of_plungers.php

If you would like to speak to one of our Tacoma drain cleaning contractors, please call 877-694-5176, or complete our online service request form.

First-Aid Kit, Sewing Kit …Toilet Repair Kit?

Every Tacoma homeowner should have certain tools and supplies on hand in case of a plumbing emergency. Here are a few bathroom plumbing supplies that you should always have on hand so that you can make a simple plumbing repair while you wait for your Tacoma plumber.

Repair Kits:

We all have to deal with a leaky sink, a toilet that won’t flush, or water that won’t turn off at some point. The best way to deal with this is to make sure you always have plumbing repair kits on hand. You can pick up simple toilet repair kits at any big box store or Tacoma hardware supply store. They generally include all the basic parts needed to repair a toilet.

Sink repair kits will generally have bolts, nuts and washers included, and some may have the stem for the handle as well.

Plumber’s Putty:

While plumber‘s putty won’t cure a leaky hose, it will certainly work in a pinch. You can buy this in small jars at most Tacoma hardware stores. It’s designed to form a temporary seal for leaky hoses or similar parts. If you discover your bathroom sink is leaking from the connector, this is the best thing to apply until you can call your professional Tacoma plumber to arrange for a more permanent fix. Having this material on hand can potentially save you lots of money in water damage repair.

Pipe Epoxy:

Epoxy is similarly not a permanent fix for a hole in a pipe or hose, but it will plug it up long enough to get it fixed. Just as with the putty, the epoxy is good to use in a pinch. The difference is the epoxy can generally be used on wet or dry surfaces, and forms a more secure bond. Use sparingly, though, as it can be very difficult to remove later.

Pipe Wrench:

You never know when you’ll need to tighten a bolt in a hard-to-reach place. Pipe wrenches are designed just for this. They are large enough to reach and grip the farthest pipes in the back of a cabinet or wall.

Washers, Bolts, Nuts:

These are so inexpensive that it’s silly to not have some extra ones on hand. You can store these in a small decorative jar or even an old coffee tin. If you have them, you won’t have to worry about running out in the middle of a repair to pick them up.

Drain Snakes:

If you discover a drain that isn’t draining properly, or worse, a toilet that keeps backing up, the easiest fix is to use a snake to remove the clog. Letting a clog go untreated will only make it worse and can potentially cost you a lot more down the road in repairs. You can pick up an inexpensive snake for around $20. Just keep it in the package and tuck it under the cabinet somewhere out of sight, and then you will have it when you need it.

A Well Stocked Toolbox:

Keep a toolbox handy and accessible. Always make sure you have all the essential tools inside it. Screwdrivers, both flat and Phillips heads, wrenches of different kinds, extra screws, hammers, a level, etc. This will prevent you from scurrying around later trying to find the misplaced tool when you need it most.

Article Source: http://www.articlesbase.com/tools-and-equipment-articles/7-must-have-bathroom-plumbing-supplies-2220294.html

Pink Sink? Rust-Stained Clothes? Iron Out the Problem

Did you know that iron is not dangerous to your health? However, I am sure you are tired of the effects of this mineral and desperately want to remove iron from water that supplies your Seattle home.

Are you tired of those nasty red stains in your sink and toilet? Does the thought of doing a laundry load of whites make you cringe because you know you’ll never see them white again? Iron in your water is a problem for many people especially those who live in rural areas dealing with well water.

First of all let’s talk about the myth that you need iron in your water for your body’s sake. This is not the same iron you get in food or in vitamin pills. This is insoluble iron and cannot be assimilated correctly into your bodies. This iron just causes problems. It clogs your pipes. It ruins your laundry, and it makes rings around your pretty white porcelain sinks, toilets and appliances.

This article will briefly explain what type of water purifier filter you will need depending on the type of iron you have your water supply and where the contamination is coming from.

Choosing the best iron filter is very important for the efficiency of the system. The wrong type of filter along with being installed in the wrong position will make it largely ineffective.  This is good reason to have your professional Seattle plumber handle the installation.

You need to have your water tested to determine the type of iron in your water supply and also to find out if there are any other minerals and chemicals that might be adding to the poor quality of the water supply. Your Seattle plumber will be able to do this kind of test for you.

Along with the testing, the source of iron contamination should be found out. Is the high content of this mineral due to iron build up in the pipes supplying your Seattle home or is it from your well water supply?

If you find that it is coming from the pipes, then you will need to install a whole house water filtration system to protect your whole plumbing system. This will prevent iron in the bathtub, shower, washing machine, toilet and drinking water. If on the other hand you discover that the contamination is coming from the well water supply you could consider the option of digging a new or deeper well. That is often a cheaper option than maintaining an iron water filter for many years.

Of course the choice of whole house water purification will depend on the above results, and your Seattle plumber will be able to advise on the best water filter system to install. But in the case that you are doing this on your own, and want to research prior to getting advice, here are the treatment options you will have:

1. Manganese Greensand Filters – To remove dissolved ferris iron, by changing it into the solid ferric iron form.
2. Whole House Iron Filter System – To remove iron as well as manganese and hydrogen sulphide or that rotten egg smell.
3. Pre sediment filter added to a whole house iron filtration system. This might help to extend the life of your iron filter cartridge and stop possible clogging of the filter.

The maintenance costs of each of the above will vary according to the pH of the water, the flow rate, how often you use the water, and the concentrations of either iron, manganese and hydrogen sulphide in the water.

Article Source: http://EzineArticles.com/?expert=Kirst_Frangs

If you are looking for a Tacoma plumbing contractor, please call 877-694-5176 or complete our online request form.

« Previous Page — Next Page »